ram ( 8-bit) rom ( 8-bit) 32 k type MN101C87A (under development) package 64 k 1.5 k 2 k lqfp064-p-1414 *lead-free mn101c87d (under planning) MN101C87A , mn101c87d minimum instruction execution time 0.1 s (at 4.5 v to 5.5 v, 20 mhz) 0.24 s (at 2.7 v to 5.5 v, 8.4 mhz) 0.48 s (at 2.3 v to 5.5 v, 4.19 mhz) * 0.24 s (at 2.0 v to 5.5 v, 2.0 mhz)* 62.5 s (at 2.0 v to 5.5 v, 32 khz) * * the lower limit for operation guarantee for eprom built-in type is 2.5 v interrupts ? reset watchdog external 0 external 1 external 2 external 3 external 4 timer 0 timer 1 timer 2 timer 3 timer 6 time base timer 7 (2 systems) serial 0 (2 systems) serial 2 a/d conversion finish automatic transfer finish fl display key scan fl display dimmer timer counter timer counter 0 : 8-bit 1 (square-wave/8-bit pwm output, event count, generation of remote control carrier, simple pulse width measurement) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, serial transfer clock) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2 : 8-bit 1 (square-wave output, pwm output, serial transf er clock, event count, simple pulse width measurement) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 2 timer counter 3 : 8-bit 1 (square-wave output, event count, generation of r emote control carrier, serial transfer clock) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 6 : 8-bit freerun timer clock source 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of osc oscillation clock frequency; 1/1, 1/128, 1/8192 of xi oscillation clock frequency interrupt source coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave output, 16-bit pwm output (cycle / duty contin uous variable), event count, pulse width measurement, input capture) clock source 1/1, 1/2, 1/4, 1/16 of system clock fr equency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 7 (2 lines) mad00050bem
MN101C87A , mn101c87d timer counter (continue) time base timer (one-minute count setting) clock source 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768, of clock source frequency watchdog timer interrupt source 1/65536, 1/262144, 1/1048576 of system clock frequency serial interface serial 0 : synchronous type/uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of osc oscilla tion clock frequency, external clock serial 2 : synchronous type/single-master i 2 c 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3; 1/2, 1/4, 1/16, 1/32 of osc oscilla tion clock frequency, external clock a/d inputs 10-bit 8-ch. (with s/h) fl (8 to 16) segments (18 to 10) digits special ports buzzer output, high-current drive port see the next page for pin assignment and support tool. mad00050bem i/o pins 26 common use specified pull-up resistor available input/output selectable (bit unit) i/o 26 output: 18 i/o: 8 p-ch. open drain (breakdown voltage ? 30 v) : fl drive: 26 specified pull-down resistor mask option: 16 high voltage pin assignment lqfp064-p-1414 * lead-free an5 / pa5 an4 / pa4 an3 / pa3 an2 / pa2 an1 / pa1 an0 / pa0 vref+ vdd1 osc2 osc1 vss xi xo mmod nrst / p27 rmout / tm0io / p10 p70 / seg7 / dgt0 p71 / seg6 / dgt1 p72 / seg5 / dgt2 p73 / seg4 / dgt3 p74 / seg3 / dgt4 p75 / seg2 / dgt5 p76 / seg1 / dgt6 p77 / seg0 / dgt7 p40 / dgt8 p41 / dgt9 p60 / dgt10 p61 / dgt11 p62 / dgt12 p63 / dgt13 p64 / dgt14 p65 / dgt15 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 dgt16 / p66 dgt17 / p67 vdd3 vdd2 led2 / p52 led1 / p51 led0 / p50 irq4 / p24 irq3 / p23 irq2 / p22 acz / irq1 / p21 irq0 / p20 tm7io / p14 drout / tm3io / p13 tm2io / p12 tm1io / p11 p87 / seg8 p86 / seg9 p85 / seg10 p84 / seg11 p83 / seg12 p82 / seg13 p81 / seg14 p80 / seg15 vpp p00 / sbo0 / txd p01 / sbi0 / rxd p02 / sbt0 p03 / sbo2 / sda p04 / sbi2 / an7 p05 / sbt2 / scl p06 / buzzer / an6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 MN101C87A mn101c87d max. transfer cycles : 255 starting factor : external request, va rious types of interrupt, software transfer mode : 1-byte transfer, wo rd transfer, burst transfer dma controller (automatic data transfer)
type mn101cf87g (under development) rom ( 8-bit) 128 k ram ( 8-bit) 4 k minimum instruction execution time 0.1 s (at 4.5 v to 5.5 v, 20 mhz) 0.24 s (at 2.7 v to 5.5 v, 8.4 mhz) 0.48 s (at 2.5 v to 5.5 v, 4.19 mhz) 62.5 s (at 2.5 v to 5.5 v, 32 khz) package lqfp064-p-1414 *lead-free support tool flash memory built-in type in-circuit emulator px-ice101c / d + px-prb101c87-lqfp064-p-1414-m (under development) mad00050bem
MN101C87A , mn101c87d mad00050bem
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general elec- tronic equipment (such as office equipment, communications equipment, measuring instruments and house- hold appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus- tion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifica- tions satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rat- ing, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
